60Si2MnA Spring Steel Springs Reference Data

60Si2MnA Spring Steel Spring Material Reference Data: 66 catalog-backed reference configurations are available for sizing review. Use the ranges below to compare the starting envelope before submitting a drawing for final quotation.

Wire diameter: 0.2-12 mm (0.0079-0.4724 in)
Outside diameter: 2.03-150.35 mm (0.0799-5.9193 in)
Inside diameter: 1.63-130.35 mm (0.0642-5.1319 in)
Free length: 3.61-442.86 mm (0.1421-17.4354 in)
Spring rate: 0.041-50.701 N/mm
Maximum load: 0.09-3258.07 N

Catalog rows are reference configurations for custom design review. Final dimensions, loads, tolerances and material certifications are confirmed during quotation.

Products Represented in This Data

These rows show which product designs are represented in the reference data. Open the matching product for geometry, quotation inputs, application guidance and RFQ details.

Conical Compression Springs10 matching rowsConical Compression Springs Application Guide
Custom-Shaped Springs1 matching rowCustom-Shaped Springs Application Guide
Cylindrical Compression Springs7 matching rowsCylindrical Compression Springs Application Guide
Double-Leg Torsion Springs2 matching rowsDouble-Leg Torsion Springs Application Guide
English-Hook Extension Springs2 matching rowsEnglish-Hook Extension Springs Application Guide
German-Hook Extension Springs6 matching rowsGerman-Hook Extension Springs Application Guide
Hairpin Springs1 matching rowHairpin Springs Application Guide
Offset-Hook Extension Springs4 matching rowsOffset-Hook Extension Springs Application Guide
Round-Hook Extension Springs3 matching rowsRound-Hook Extension Springs Application Guide
Single-Leg Torsion Springs4 matching rowsSingle-Leg Torsion Springs Application Guide
Straight-Leg Torsion Springs3 matching rowsStraight-Leg Torsion Springs Application Guide
Torsion Bar Springs1 matching rowTorsion Bar Springs Application Guide

Engineering Material Reference

60Si2MnA Spring Steel is included here as an engineering material reference. This page summarizes published material properties and shows catalog-backed spring rows when they exist.

Primary grade	GB/ T 1222 60Si2MnA
Standards	GB/ T 1222; EN 56Si7/ Si-Mn
Corrosion behavior	low in bare condition; specify passivation, phosphate, zinc, black oxide, oil or coating when corrosion protection is required
Temperature note	screening range -40 to 180 C, to be confirmed against final stress and environment
Tensile strength	1000-1800 MPa
Elastic modulus	200-210 GPa
Shear modulus	77-82 GPa
Density	7.85 g/cm3

Matching Reference Configurations

Model	Product	Wire / thickness	OD	ID	Free length	Rate (N/mm)	Material	Max load (N)
SE-020-0020-0138-0455	Offset-Hook Extension Springs	0.2 mm	2.03 mm	1.63 mm	13.77 mm	0.046	60Si2MnA Spring Steel	0.19
SC-030-0026-0128-0311	Tower-Shaped Compression Springs	0.3 mm	2.6 mm	2 mm	12.75 mm	0.257	60Si2MnA Spring Steel	0.73
SC-030-0029-0036-0122	Cylindrical Compression Springs	0.3 mm	2.89 mm	2.29 mm	3.61 mm	0.731	60Si2MnA Spring Steel	0.69
SC-030-0044-0039-0078	Tower-Shaped Compression Springs	0.3 mm	4.42 mm	3.82 mm	3.93 mm	0.179	60Si2MnA Spring Steel	0.2
SC-030-0045-0046-0029	Cylindrical Compression Springs	0.3 mm	4.53 mm	3.93 mm	4.56 mm	0.132	60Si2MnA Spring Steel	0.13
SC-030-0046-0118-0258	Tower-Shaped Compression Springs	0.3 mm	4.55 mm	3.95 mm	11.83 mm	0.041	60Si2MnA Spring Steel	0.09
SE-040-0030-0208-0571	German-Hook Extension Springs	0.4 mm	2.95 mm	2.15 mm	20.77 mm	0.382	60Si2MnA Spring Steel	2.46
SC-040-0042-0090-0373	Variable-Diameter Compression Springs	0.4 mm	4.22 mm	3.42 mm	9.01 mm	0.236	60Si2MnA Spring Steel	0.13
SC-040-0048-0103-0144	Tower-Shaped Compression Springs	0.4 mm	4.83 mm	4.03 mm	10.34 mm	0.196	60Si2MnA Spring Steel	0.54
SC-040-0057-0137-0309	Tower-Shaped Compression Springs	0.4 mm	5.73 mm	4.93 mm	13.73 mm	0.08	60Si2MnA Spring Steel	0.25
SC-050-0046-0140-0382	Variable-Diameter Compression Springs	0.5 mm	4.58 mm	3.58 mm	14.03 mm	0.481	60Si2MnA Spring Steel	1.14
SE-050-0049-0255-0531	German-Hook Extension Springs	0.5 mm	4.94 mm	3.94 mm	25.53 mm	0.175	60Si2MnA Spring Steel	1.31
SC-050-0056-0140-0135	Cylindrical Compression Springs	0.5 mm	5.6 mm	4.6 mm	13.98 mm	0.225	60Si2MnA Spring Steel	0.5
SW-050-0062-1535-0726	Wire-Formed Components	0.5 mm	6.18 mm	5.18 mm	153.46 mm	0.503	60Si2MnA Spring Steel	21.48
SE-060-0048-0294-0470	Round-Hook Extension Springs	0.6 mm	4.78 mm	3.58 mm	29.43 mm	0.47	60Si2MnA Spring Steel	3.96
SE-060-0060-0376-0436	Offset-Hook Extension Springs	0.6 mm	5.98 mm	4.78 mm	37.62 mm	0.165	60Si2MnA Spring Steel	1.68
ST-060-0067-0124-0620	Straight-Leg Torsion Springs	0.6 mm	6.72 mm	5.52 mm	12.37 mm	0.062	60Si2MnA Spring Steel	7.21
SC-060-0083-0148-0212	Tower-Shaped Compression Springs	0.6 mm	8.31 mm	7.11 mm	14.81 mm	0.151	60Si2MnA Spring Steel	0.26
SE-080-0044-0408-0472	Offset-Hook Extension Springs	0.8 mm	4.4 mm	2.8 mm	40.76 mm	2.275	60Si2MnA Spring Steel	15.79
SC-080-0060-0164-0094	Conical Compression Springs	0.8 mm	5.96 mm	4.36 mm	16.45 mm	2.103	60Si2MnA Spring Steel	5.47
ST-080-0069-0118-0703	Double-Leg Torsion Springs	0.8 mm	6.88 mm	5.28 mm	11.76 mm	0.274	60Si2MnA Spring Steel	25.4
SE-080-0076-0161-0489	Round-Hook Extension Springs	0.8 mm	7.62 mm	6.02 mm	16.12 mm	1.449	60Si2MnA Spring Steel	5.28
SC-080-0080-0345-0329	Tower-Shaped Compression Springs	0.8 mm	7.97 mm	6.37 mm	34.52 mm	0.413	60Si2MnA Spring Steel	2.68
SE-080-0098-0260-0496	English-Hook Extension Springs	0.8 mm	9.8 mm	8.2 mm	25.95 mm	0.226	60Si2MnA Spring Steel	1.66
SC-080-0108-0143-0037	Conical Compression Springs	0.8 mm	10.83 mm	9.23 mm	14.33 mm	0.276	60Si2MnA Spring Steel	0.43
SE-100-0062-0548-0550	Round-Hook Extension Springs	1 mm	6.16 mm	4.16 mm	54.77 mm	1.539	60Si2MnA Spring Steel	28.21
ST-100-0066-0159-0700	Single-Leg Torsion Springs	1 mm	6.58 mm	4.58 mm	15.91 mm	0.633	60Si2MnA Spring Steel	44.96
SC-100-0087-0275-0390	Tower-Shaped Compression Springs	1 mm	8.66 mm	6.66 mm	27.51 mm	1.324	60Si2MnA Spring Steel	7.35
SC-100-0129-0195-0415	Conical Compression Springs	1 mm	12.91 mm	10.91 mm	19.52 mm	0.527	60Si2MnA Spring Steel	2.13
SW-100-0150-1851-0799	Torsion Bar Springs	1 mm	15.03 mm	13.03 mm	185.11 mm	1.49	60Si2MnA Spring Steel	55.9
SW-100-0181-1764-0739	Wire-Formed Components	1 mm	18.09 mm	16.09 mm	176.41 mm	0.213	60Si2MnA Spring Steel	4.61
SE-150-0073-0704-0535	German-Hook Extension Springs	1.5 mm	7.26 mm	4.26 mm	70.36 mm	7.786	60Si2MnA Spring Steel	117.86

Using This Material Data

cold coiling or hot coiling, stress relief, shot peening and presetting may be specified; electroplating high-strength steel requires hydrogen-embrittlement controls

Need to choose between grades? Material selection belongs in the Materials section rather than this data page. Open Carbon & Alloy Spring Steels →

CustomSprings Engineering Catalog

Request This Spring

Send your dimensions, quantity and drawing for engineering review.

Request a Custom Quote

Fields marked * are required. A drawing is recommended for accurate review.

Spring Requirements

Spring Type Wire / Thickness (mm) Outside Diameter / Envelope (mm) Inside Diameter / Bore (mm) Free Length / Height (mm) Spring Rate / Torque Load / Torque Coils / Turns / Leaves Quantity * Material Finish Drawing PDF, CAD, image or ZIP; maximum 10 MB.

Contact Information

Company Contact Name * Email * Phone / WhatsApp Country / Region Application

Notes

Frequently Asked Questions

Can CustomSprings manufacture springs in 60Si2MnA Spring Steel?

The material is included in the CustomSprings material library for RFQ screening. Final feasibility depends on wire or strip form, size, heat treatment, load, environment and quantity.

Does the material page guarantee certified properties?

No. The material values are engineering reference data. Certified properties or test reports must be specified during production quotation.

What if there are no matching reference rows?

Use the RFQ form with your drawing and application data. The material can still be reviewed as a made-to-drawing option.