316 Stainless Steel Springs Reference Data

316 Stainless Steel Spring Material Reference Data: 66 catalog-backed reference configurations are available for sizing review. Use the ranges below to compare the starting envelope before submitting a drawing for final quotation.

Wire diameter: 0.15-12 mm (0.0059-0.4724 in)
Outside diameter: 1.89-103.26 mm (0.0744-4.0654 in)
Inside diameter: 1.34-89.26 mm (0.0528-3.5142 in)
Free length: 2.9-296.27 mm (0.1142-11.6642 in)
Spring rate: 0.013-195.575 N/mm
Maximum load: 0.02-16721.66 N

Catalog rows are reference configurations for custom design review. Final dimensions, loads, tolerances and material certifications are confirmed during quotation.

Products Represented in This Data

These rows show which product designs are represented in the reference data. Open the matching product for geometry, quotation inputs, application guidance and RFQ details.

Conical Compression Springs5 matching rowsConical Compression Springs Application Guide
Custom-Shaped Springs2 matching rowsCustom-Shaped Springs Application Guide
Cylindrical Compression Springs2 matching rowsCylindrical Compression Springs Application Guide
English-Hook Extension Springs9 matching rowsEnglish-Hook Extension Springs Application Guide
German-Hook Extension Springs2 matching rowsGerman-Hook Extension Springs Application Guide
Offset-Hook Extension Springs4 matching rowsOffset-Hook Extension Springs Application Guide
Round-Hook Extension Springs5 matching rowsRound-Hook Extension Springs Application Guide
Single-Leg Torsion Springs5 matching rowsSingle-Leg Torsion Springs Application Guide
Straight-Leg Torsion Springs2 matching rowsStraight-Leg Torsion Springs Application Guide
Torsion Bar Springs4 matching rowsTorsion Bar Springs Application Guide
Tower-Shaped Compression Springs10 matching rowsTower-Shaped Compression Springs Application Guide
Variable-Diameter Compression Springs14 matching rowsVariable-Diameter Compression Springs Application Guide

Engineering Material Reference

316 Stainless Steel is included here as an engineering material reference. This page summarizes published material properties and shows catalog-backed spring rows when they exist.

Primary grade	UNS S31600/ S31603; EN 1.4401/ 1.4404
Standards	ASTM A313/ A580; EN 1.4401/ 1.4404; JIS SUS316; GB/ T
Corrosion behavior	higher chloride and marine corrosion resistance than 302/304 stainless grades
Temperature note	screening range -184 to 288 C, to be confirmed against final stress and environment
Tensile strength	860-1895 MPa
Elastic modulus	190-200 GPa
Shear modulus	73-77 GPa
Density	8.00 g/cm3

Matching Reference Configurations

Model	Product	Wire / thickness	OD	ID	Free length	Rate (N/mm)	Material	Max load (N)
SE-015-0019-0080-0530	Offset-Hook Extension Springs	0.15 mm	1.89 mm	1.59 mm	8.04 mm	0.021	316 Stainless Steel	0.06
SC-020-0026-0029-0137	Tower-Shaped Compression Springs	0.2 mm	2.6 mm	2.2 mm	2.9 mm	0.088	316 Stainless Steel	0.02
SC-030-0024-0054-0036	Variable-Diameter Compression Springs	0.3 mm	2.35 mm	1.75 mm	5.38 mm	0.772	316 Stainless Steel	1.1
SE-030-0032-0113-0453	English-Hook Extension Springs	0.3 mm	3.22 mm	2.62 mm	11.34 mm	0.093	316 Stainless Steel	0.25
ST-030-0037-0031-0630	Straight-Leg Torsion Springs	0.3 mm	3.66 mm	3.06 mm	3.12 mm	0.013	316 Stainless Steel	0.48
SC-030-0039-0056-0121	Variable-Diameter Compression Springs	0.3 mm	3.91 mm	3.31 mm	5.6 mm	0.099	316 Stainless Steel	0.06
SC-030-0055-0130-0385	Variable-Diameter Compression Springs	0.3 mm	5.5 mm	4.9 mm	12.99 mm	0.018	316 Stainless Steel	0.05
SW-030-0062-1182-0758	Wire-Formed Components	0.3 mm	6.21 mm	5.61 mm	118.23 mm	0.035	316 Stainless Steel	0.81
SE-040-0022-0090-0541	Offset-Hook Extension Springs	0.4 mm	2.25 mm	1.45 mm	9.01 mm	2.768	316 Stainless Steel	6.12
SE-040-0038-0099-0481	Round-Hook Extension Springs	0.4 mm	3.83 mm	3.03 mm	9.94 mm	0.336	316 Stainless Steel	1.07
SC-040-0051-0112-0116	Tower-Shaped Compression Springs	0.4 mm	5.11 mm	4.31 mm	11.19 mm	0.121	316 Stainless Steel	0.33
SC-040-0059-0091-0239	Tower-Shaped Compression Springs	0.4 mm	5.93 mm	5.13 mm	9.14 mm	0.074	316 Stainless Steel	0.08
SC-050-0023-0037-0328	Variable-Diameter Compression Springs	0.5 mm	2.34 mm	1.34 mm	3.71 mm	26.222	316 Stainless Steel	27.01
SC-050-0028-0062-0273	Tower-Shaped Compression Springs	0.5 mm	2.85 mm	1.85 mm	6.22 mm	7.552	316 Stainless Steel	10.35
ST-050-0030-0069-0707	Single-Leg Torsion Springs	0.5 mm	2.99 mm	1.99 mm	6.93 mm	0.096	316 Stainless Steel	12.04
SC-050-0052-0137-0293	Cylindrical Compression Springs	0.5 mm	5.17 mm	4.17 mm	13.73 mm	0.308	316 Stainless Steel	0.93
SW-050-0088-0477-0789	Torsion Bar Springs	0.5 mm	8.82 mm	7.82 mm	47.68 mm	0.097	316 Stainless Steel	0.54
SW-050-0091-1468-0722	Custom-Shaped Springs	0.5 mm	9.07 mm	8.07 mm	146.85 mm	0.143	316 Stainless Steel	4.43
SW-050-0147-1980-0785	Torsion Bar Springs	0.5 mm	14.67 mm	13.67 mm	197.99 mm	0.082	316 Stainless Steel	3.46
SE-060-0035-0410-0511	Offset-Hook Extension Springs	0.6 mm	3.53 mm	2.33 mm	41.05 mm	0.85	316 Stainless Steel	12.05
SE-060-0052-0360-0561	Round-Hook Extension Springs	0.6 mm	5.24 mm	4.04 mm	36 mm	0.249	316 Stainless Steel	2.14
SC-060-0074-0101-0208	Variable-Diameter Compression Springs	0.6 mm	7.43 mm	6.23 mm	10.11 mm	0.295	316 Stainless Steel	0.44
SC-060-0090-0069-0226	Variable-Diameter Compression Springs	0.6 mm	8.95 mm	7.75 mm	6.89 mm	0.234	316 Stainless Steel	0.22
ST-080-0124-0134-0610	Straight-Leg Torsion Springs	0.8 mm	12.42 mm	10.82 mm	13.36 mm	0.122	316 Stainless Steel	14.85
ST-100-0044-0113-0618	Single-Leg Torsion Springs	1 mm	4.41 mm	2.41 mm	11.33 mm	1.378	316 Stainless Steel	184.11
SE-100-0057-0671-0461	German-Hook Extension Springs	1 mm	5.73 mm	3.73 mm	67.11 mm	1.495	316 Stainless Steel	27.96
SE-100-0086-0231-0546	English-Hook Extension Springs	1 mm	8.64 mm	6.64 mm	23.12 mm	1.476	316 Stainless Steel	5.38
SC-100-0158-0222-0028	Conical Compression Springs	1 mm	15.81 mm	13.81 mm	22.19 mm	0.151	316 Stainless Steel	0.28
SE-120-0069-0384-0446	English-Hook Extension Springs	1.2 mm	6.92 mm	4.52 mm	38.41 mm	5.03	316 Stainless Steel	44.11
SE-120-0073-0651-0494	Round-Hook Extension Springs	1.2 mm	7.32 mm	4.92 mm	65.08 mm	1.853	316 Stainless Steel	23.6
SC-120-0128-0448-0099	Tower-Shaped Compression Springs	1.2 mm	12.81 mm	10.41 mm	44.82 mm	0.478	316 Stainless Steel	5.44
ST-120-0175-0065-0684	Single-Leg Torsion Springs	1.2 mm	17.52 mm	15.12 mm	6.5 mm	1.286	316 Stainless Steel	42.7

Using This Material Data

cold forming, stress relief and passivation are common; spring temper and magnetic response must be confirmed by grade and cold work

Need to choose between grades? Material selection belongs in the Materials section rather than this data page. Open Stainless Steel Spring Materials →

CustomSprings Engineering Catalog

Request This Spring

Send your dimensions, quantity and drawing for engineering review.

Request a Custom Quote

Fields marked * are required. A drawing is recommended for accurate review.

Spring Requirements

Spring Type Wire / Thickness (mm) Outside Diameter / Envelope (mm) Inside Diameter / Bore (mm) Free Length / Height (mm) Spring Rate / Torque Load / Torque Coils / Turns / Leaves Quantity * Material Finish Drawing PDF, CAD, image or ZIP; maximum 10 MB.

Contact Information

Company Contact Name * Email * Phone / WhatsApp Country / Region Application

Notes

Frequently Asked Questions

Can CustomSprings manufacture springs in 316 Stainless Steel?

The material is included in the CustomSprings material library for RFQ screening. Final feasibility depends on wire or strip form, size, heat treatment, load, environment and quantity.

Does the material page guarantee certified properties?

No. The material values are engineering reference data. Certified properties or test reports must be specified during production quotation.

What if there are no matching reference rows?

Use the RFQ form with your drawing and application data. The material can still be reviewed as a made-to-drawing option.